AT&T 905 User Manual download pdf (Page 2)

INSTALLATION

NOTE: This telephone requires a

modular telephone jack.

Table

If you have a wall-mounted telephone,

remove the telephone from the wall

and follow these instructions:

1 Remove the base.

2 Connect line cord to telephone.

Plug the line cord into the jack

labeled TEL LINE on the back

of the phone.

3 Attach the base.

Turn the base so that the larger

end of the base is toward the top

of the telephone. Attach the base

by inserting the tabs into the slots.

Push down on the large end of the

base to lock it into place.

4 Connect the line cord to your

modular jack.

Plug the free end of the line cord

into a modular jack. Make sure it

snaps firmly into place.

5 Connect handset to telephone.

Plug the coiled cord into the

handset jack on the side of the

phone. Plug the other end of the

coiled cord into the handset, and

then hang up.

6 Check for dial tone.

Lift the handset and listen for a

dial tone. If you cannot hear a dial

tone, turn to “In Case of Difficulty.”

Wall

1 Remove the base.

2 Thread one end of the line cord

under the three holders inside

the base.

Thread one end of the line cord

under the three holders and

through the slot in the base,

leaving about two inches extended

beyond the base (Figure 1). Wrap

the remaining line cord around the

posts leaving about three inches

free on the end.

3 Attach the base.

Turn the base so that the larger

end is toward the bottom of the

telephone. Attach the base by

inserting the tabs into the slots.

Push down on the large end of

the base so the tabs are in the

slots, and the base locks in place.

4 Connect the line cord to the

telephone.

Plug one end of the line cord into

the jack labeled TEL LINE on the

back of the phone.

5 Reverse the handset tab.

This tab holds the handset when

you hang up. Hold down the

switchhook, and slide the tab up

and out of its slot. Turn the tab

so that the end with the “hook” is

up. Then insert the tab back into

its slot (Figures 2A–2C).

6 Connect the line cord to modular

wall jack and mount phone onto

wall jack.

Make sure the cord snaps firmly

into place. Place the phone on the

wall jack mounting studs and pull

down until it is held securely.

Follow Steps 5 and 6 under “Table”

Installation.

Dial Mode Selection

This product will work with tone or

dial pulse (rotary) service. The Dial

Mode switch, which is located on

the bottom of the set underneath

the removable base, is pre-set in

the touch tone (TT) mode. Make

sure you choose the correct dialing

method; touch tone dialing will not

work if you have dial pulse service.

If you have dial pulse service, you

will need to follow these instructions.

1 Remove the base.

2 Set the Dial Mode switch to DP

(dial pulse).

3 Attach the base.

Even when set to dial pulse service,

the phone can be switched temporarily

to tone, for access to services that

require tone signaling (such as

banking services). See “Temporary

Tone Dialing” for instructions.

MEM 1

MEM 2

MEM 3

MEM 4

MEM 5

MEM 6

MEM 7

MEM 8

MEM 9

THIS NUMBER

MEM 1

MEM 2

MEM 3

MEM 4

MEM 5

MEM 6

MEM 7

MEM 8

MEM 9

THIS NUMBER

MEM 1

MEM 2

MEM 3

MEM 4

MEM 5

MEM 6

MEM 7

MEM 8

MEM 9

THIS NUMBER

Figure 1 Figure 2A Figure 2B Figure 2C

Thread cord

under three

holders

1

1 2 3 4 5 6

Comments to this Manuals

No comments